ServicesEquipment Installation
Pool Equipment Installation in Florence
When a pump, filter or heater has reached the end of its life, we help you pick a replacement that fits your pool and your budget. We install it, test it and send you photos of the old setup, the new one and everything we changed.
New equipment, chosen for your pool
Equipment installation means replacing or adding the machines that keep your water moving, filtered, sanitized and warm. That covers pumps, filters, heaters and heat pumps, salt chlorine generators, booster pumps for pressure-side cleaners, and automation controls. Most calls come from a homeowner whose pump has gone loud or quit, or whose filter can no longer keep up with the dust after a summer storm.
We start by looking at what you already have. Sometimes a part can be fixed, and if so we will say that and point you to our pool repair service. When replacement really is the better choice, we size the new unit to your pool's volume and plumbing rather than handing you the biggest model on the truck.
You see the whole job. We photograph the pad before we touch it, the plumbing as we rework it and the finished installation running, so you know exactly what was installed at your home and why.
What an installation includes
- 01
Sizing and a written recommendation
We measure your pool, check pipe size and look at how far the pad sits from the water. Then we recommend equipment that matches, with the reasons spelled out.
- 02
Removal of the old unit
We disconnect and haul away the old pump, filter or heater so it is not left sitting beside your house.
- 03
Clean plumbing and unions
New PVC is cut square, primed and glued, with unions where they make future service easier. Crooked or patched pipe from earlier work gets straightened out while the pad is open.
- 04
Electrical hookup and bonding
We connect the new equipment to the existing circuit and reattach the bonding wire, which is easy to skip and important to get right. If the circuit needs upgrading, we tell you before the work starts.
- 05
Start-up and settings
We prime the system, check for drips, set pump speeds and run times, and confirm the pressure reading on the filter is where it should be.
- 06
Photos and a walkthrough
You get before and after photos, plus a short explanation of how to run your new equipment and what the gauges should read.
Questions about Equipment Installation?
Call(520) 645-2946Signs it may be time for new equipment
A pump that screeches or hums
Grinding or whining usually points to worn motor bearings. A hum with no spin often means a failed capacitor or a seized motor.
Water dripping at the pad
A steady drip from the pump seal or a cracked filter tank wastes water and chemicals. On older equipment, replacement often makes more sense than another round of patches.
Cloudy water that will not clear
If your chemistry is balanced and the water still looks dull, the filter may be undersized or worn out. Torn cartridges and broken grids let fine dirt slip back into the pool.
High power bills from an old pump
Single-speed pumps run flat out the whole time. A variable-speed pump can turn down for daily filtering and use far less electricity, which adds up through a long Arizona swim season.
A heater that cuts out or will not light
Rust, scale on the heat exchanger and repeated error codes are common signs a heater is near the end.
How installation day works
- 1
Free quote by phone and a look at your pad
Call us, tell us what is happening, and we will set a time to see your equipment. We take photos and explain your options, including whether a repair would do.
- 2
Your approval
You get a written estimate listing the equipment and the labor. Nothing is ordered until you say yes.
- 3
Installation
Most pump and filter swaps take a few hours. We shut off power at the breaker, remove the old unit, set the new one and rework the plumbing. Your yard stays tidy, and we clear away cut pipe and packaging before we leave.
- 4
Testing and handoff
We run the system, check every joint and set the schedule. You receive the photos and a quick rundown of how to use the new controls.
What affects the cost of installation
Every pool pad is different, so we price each job after seeing it. Your estimate lists the equipment and the labor separately, so you can see where the money goes. These are the things that move the number most.
- Type and size of equipment
- A basic cartridge filter costs less than a large DE filter, and a heat pump costs more than a booster pump. Pool volume decides how big the unit needs to be.
- Brand and features
- Variable-speed pumps, salt systems and automation add upfront cost but can lower running costs or save you time.
- Plumbing changes
- Moving from an old unit to a new one with different port positions often means new pipe and fittings. Undersized or brittle sun-damaged pipe may need replacing at the same time.
- Electrical work
- A heater or automation panel may need a new circuit or added wiring. We tell you up front if that applies to your home.
Equipment installation questions
Can you install equipment I bought myself?
Often yes. We will check that the unit is the right size and type for your pool before we install it. If it is a poor match, we will tell you why so you can decide whether to return it.
Should I go with a variable-speed pump?
For most pools, yes. Federal efficiency rules mean most replacement pumps sold today are variable-speed anyway. They run quietly at low speeds for everyday filtering and can cut electricity use considerably.
Is a salt system right for my pool?
A salt chlorine generator makes chlorine from dissolved salt, so you handle fewer jugs and tablets. It does need a cell that is cleaned of scale regularly, which matters with the hard water in this area. We will walk you through the upkeep before you decide.
Will I be without a working pool for long?
Usually just for the day of installation. A pump or filter swap is commonly finished in a few hours, and heaters or automation may take longer if wiring is involved.
Can you take care of the new equipment afterward?
Yes. Many customers add our weekly pool cleaning, which includes chemicals in the monthly price and has no contract. We can also schedule filter cleaning to keep a new filter working the way it should.
Ready to replace that tired equipment?
Tell us what your pump, filter or heater is doing, and we will set up a visit and give you clear options. We serve Florence and nearby towns like San Tan Valley, Coolidge and Queen Creek.